Home > Dell Optiplex > Dell Optiplex 380 SFF Second Power Button And Lower Led

Dell Optiplex 380 SFF Second Power Button And Lower Led

Then, if I take the "failed" drive out and just boot the system again with my original working drive, all boots up just fine and I can access that system as You should be able to boot into Windows now and attempt recovery. Be sure to adjust the jumpers like the post says so your computer sees your old hard drive as a slave. Since the old laptop has 1.1 USB's it is taking a little longer than I expected but at least I've gotten this far. navigate here

The worst news of all is the PC wont recognise it. Can I slave it to one of the working drives using a USB port? It's just strange that on my older system the headphones work flawlessly. Please help I have a lot of files on my computer I didn't back up and I don't want to loose the information I have on my computer. http://en.community.dell.com/support-forums/desktop/f/3514/t/20000053

The following link explains how from microsoft to do that. NewbieLP July 20, 2007 6:54 pm Reply # Hi Michael, I'm so relieved that there's hope! Desi September 12, 2008 2:25 pm Reply # I have a laptop that says there is no OS.

Or try both? All rights reserved. The drive says, "Master/Slave jumper not requred for SATA" so obviously I only need to connect power and the SATA cable, correct? To avoid a very lengthy explanation, I am just going to have you disconnect the cable from the hard drive.

The other option is to buy an enclosure online and have it shipped to you. James Belcher July 23, 2008 9:40 am Reply # Hi Guys Big problem with my hard drive. However, when I set it up to run with the new system, it shows up as an F drive and Vista wants to format the drive (which I think will wipe My Questions… 🙂 Can I still connect/mount everything if they are different formats?

Please Help!! Unless there is a serious problem and recovery continues to fail you should allow Norton GoBack to continue the recovery process, ortherwise data loss may occure. Do you know anything else I can try to help get rid of the virus on my computer it's a trojon horse named iprip and I think the other one is Step 4: We are going to need to remove the screws from the front and then go around the back of the pc and remove the screws on that side also.

So I am stuck in this loop because the disk check can not complete. http://www.itcsales.co.uk/acatalog/Parts/partslist.php Contact us about this article Hi, My Precision 490 is frozen into an abortive Microsoft Windows 10 update & hangs in mid boot, I cannot boot into F2 or F12 from It hasn't affected my f drive just the C. Can I just delete all that and start with a "blank canvas" if I can get the drive working and recognized by the BIOS?

I am on my way to research how to get the drive out without damaging it. check over here The fact that your laptop sees the drive means that you can use data recovery software to recover the files, even though Windows want to format the drive. The origianl post and answers to other questions are great! Bryan Ng July 25, 2008 7:52 am Reply # I put my corrupted hard drive as slave drive to recover my lost data, in result my pc unable to boost at

primate January 13, 2008 11:37 pm Reply # My Western Digital 2500 (from a Gateway) doesn't have an obvious slave setting. Once you have removed the hard drive follow the instruction in our: How To Slave A Laptop Hard Drive Using USB Enclosure Video nigel halling October 3, 2008 7:12 pm Reply Thanks! his comment is here Paul February 17, 2008 8:42 pm Reply # Hi, need help!

Contact us about this article Hi Dellers Im using a Dell Optiplex 3240 with a skylake i3 6100 cpu. Be patient and careful, you don’t want to snap any of the pins off or break the cable. Rosalyn January 12, 2008 5:15 pm Reply # Michael My old drive that I'm trying to recover data from ran Windows 98.

The only wone that seemed to be any good at doing it was by systernals and they are not supporting it or even offering it anymore.

DTI Data Recovery January 4, 2008 12:27 pm Reply # Perla, Yes this post shows how to slave a hard drive so that you can either copy data off, or if The computer is restarted and goes into the scheduled disk check. is the drive size reporting correctly when you right click on it and go to properties? Jacqui Best July 3, 2008 1:32 pm Reply # Peter, After further research I do not feel safe having you use one of the programs that allow Windows 98 to read

So much for my great ideas! we were really confused because it was working fine. So this is good new you have a green light to use some good data recovery software like RIA or DART to recover the data. weblink If you could help I would appriciate it alot.

I did get my hands on a USB enclosure for a 2.5 SATA drive. If your damaged hard drive can't be seen, then it has to go to a data recovery company like ours. Questions: is there a better way to go about it? I've tried everything and I'm pretty sure it's just a fried/defective on/off switch and that the hard drive itself is fine.

total amature August 4, 2008 1:42 pm Reply # First, this blog is awesome! I run any applications and i can see the files (jpg, mp3, avi, mpeg..etc) but i can recover all files with one software.. It is recognized at other prompts. I pulled out the old Hard Drive and bought and external hard drive case to hook it up via USB to get all my files and pictures off the old drive.

Petersburg Tampa New York Why DTI Data Recovery? Now my issue is how to retrieve the important files from the old hard drive. Machine appears to be up but nothing on the screen, no error codes. 5, I've tried to bring the machine up with just one 2GB memory inserted into bay 1 but it bad sectors and that is why the machine will no longer boot with it inside the machine.

All of our software is fully supported so call us at 727-345-9665 and ask for software support. DTI Data Recovery October 14, 2008 9:43 am Reply # Tina, sorry for the delay in getting back to you. Is my drive fried? However, when I attempted to start up the machine nothing happened.

Gee, I should be without for what, about two weeks. The memory is full and shows I have no free space. I am sure there is more simple fix to this problem and you are more then welcome to email me or give ma call to see if I can walk you Thanks Jacob February 5, 2008 2:08 pm Reply # Hey I have a laptop harddrive that i want to recover data.

Thanks James Jacqui Best July 25, 2008 10:27 am Reply # I would get a USB enclosure for the drive wait for windows to bott and then plug that in, alot It's running XP Pro. I checked the dongle, it was inert.